Skip to content- Ø 150mm (6inch), Supports
- £ 72,00
- The Retrofit base support is adjustable from 0mm to 120mm from the wall, it can be used in conjunction with 90° or 135° tees when fitted directly above. This item can also be used as a load bearing intermediate support on longer flue runs and can be retro fitted to make installation simpler. One support to be used on most…
- Add to basket
- Ø 150mm (6inch), Supports
- £ 203,00
- Adjustable Base Supports are used internally or externally to provide vertical support to the chimney. This support has a small levelling adjustment of 50mm to 80mm from the wall surface. Only recommended fixings should be used to fit this base support to the building surface.
- Add to basket
- Ø 150mm (6inch), Terminals
- £ 113,00
- Standard rain cap terminal with added 25mm square wire mesh to stop birds or vermin entering and blocking the flue way. Suitable for all fuel except gas.
- Add to basket
- Accessories, Ø 150mm (6inch)
- £ 44,00
- The Wall Sleeve is used to protect the chimney in the wall passage when the flue system passes to the outside wall. The gap between the flue and the Wall Sleeve can be filled with Rockwool. If going through the wall at 45 degrees, you will have to taper-cut the sleeve so that it fits flush in the wall. It…
- Add to basket
- Accessories, Ø 150mm (6inch)
- £ 185,00
- Mesh kit. For use when your flue passes through a loft space. The loft mesh kit is used to meet building regulations. Within the loft area the flue system must be boxed in or properly enclosed. This is in order to avoid combustible materials either being placed to close to or falling against the chimney. The system makes the installation…
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 41,00
- The Finishing Plate comes in two parts and is used to tidy the area around the flue as it passes through a non-combustible wall. This plate is attached to the wall where the flue is passing through between 90° and 60°. Use silicone and screws to secure against the wall.
- Add to basket
- Accessories, Ø 150mm (6inch)
- £ 44,00
- The Adjustable Wall Sleeve is used to protect the chimney in the wall passage when the flue system passes to the outside wall. The gap bewteen the flue and the Wall Sleeve can be filled with rockwool. This Wall Sleeve is precut at 45°, and is adjustable so it can be manually extended within wall.
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 41,00
- The Finishing Plate comes in two parts and is used to tidy the area around the flue as it passes through a non-combustible wall. This plate is attached to the wall where the flue is passing through between 45° and 60°. Use silicone and screws to secure against the wall.
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 40,00
- Our Base Cap with Drain is an essential component designed to cap off the bottom or unused end of a 90/135 Tee. It is typically fitted to the bottom of a base support to allow easy removal for sweeping and access, ensuring convenient maintenance of your flue system. This versatile part includes a 10mm threaded drain, which permits the connection…
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 341,00
- Our 90° Tee is a versatile component used when connecting the flue to the rear outlet of an appliance, especially when dealing with wood-burning stoves. This Tee features a 450mm branch, enabling direct installation onto the back of a wood-burning stove and passing through a standard brick wall. It is suitable for use with a wide range of solid fuel…
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 127,00
- Our 90° Tee is a vital component, typically used when connecting the flue to the rear outlet of an appliance. This Tee is specifically designed to facilitate this connection, ensuring optimal performance and safety for a variety of solid fuel and gas/oil appliances. It is suitable for use with woodstoves, gas coal effect fires, oil boilers, gas boilers, and various…
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 341,00
- Our Long 135° Tee is an essential component designed for providing convenient cleaning access at the base of your chimney. It serves as the first piece to be installed on the external wall and enables easy cleaning of the flue, ensuring your flue system remains efficient and well-maintained. This versatile Tee is suitable for use with a wide range of…
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 188,00
- Our 135° Tee is a crucial component when you require cleaning access at the base of your chimney. It serves as the first piece to be installed on the external wall, providing an easy and efficient way to clean the flue. The Tee's design ensures that it doesn't impede the flow of flue gases, contributing to the optimal performance of…
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 76,00
- Our 2-Segment 45° Bend is a crucial component for managing offset details in your chimney system. This bend is designed to provide the flexibility needed for offsetting your flue, ensuring that it is compatible with a variety of solid fuel and gas/oil appliances. It is suitable for use with woodstoves, gas coal effect fires, oil boilers, gas boilers, and other…
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 126,00
- Our 3-Segment 90° Bend is a vital component designed to assist in managing offset details within your chimney system. This bend provides the flexibility needed to create precise angles and offsets, ensuring it is compatible with a range of solid fuel and gas/oil appliances. It is suitable for use with woodstoves, gas coal effect fires, oil boilers, gas boilers, and…
- Add to basket
- Ø 150mm (6inch), Pipes
- £ 42,00
- Our Rigid Fixed 100mm Pipe is a reliable and essential component designed to facilitate the efficient venting of solid fuel and gas/oil appliances, including woodstoves, gas coal effect fires, oil boilers, gas boilers, and other solid fuel devices. With an effective installed length of 65mm, this pipe is ideal for specific installation requirements.
- Add to basket
- Ø 150mm (6inch), Pipes
- £ 49,00
- Our Rigid Fixed 250mm Pipe, with an effective installed length of 215mm, is a reliable and essential component designed to facilitate the efficient venting of solid fuel and gas/oil appliances. This pipe is versatile and suitable for use with various heating appliances, including woodstoves, gas coal effect fires, oil boilers, gas boilers, and other solid fuel devices.
- Add to basket
- Ø 150mm (6inch), Pipes
- £ 83,00
- Our Rigid Fixed 500mm Pipe, with an effective installed length of 465mm, is a durable and essential component designed to facilitate the efficient venting of solid fuel and gas/oil appliances. This pipe is suitable for use with a wide range of heating appliances, including woodstoves, gas coal effect fires, oil boilers, gas boilers, and other solid fuel devices.
- Add to basket
- Ø 150mm (6inch), Supports
- £ 64,00
- The Heavy duty roof Support will rotate on 2 screws so that the flue can be installed vertically through the roof. The Roof Support is attached to the rafters in the roof space, allowing a fixed support before the Flue leaves the structure of the building. The larger plates offer more support than the standard -067 roof support. See loading…
- Add to basket
- Adaptors, Ø 150mm (6inch)
- £ 40,00
- Universal adaptor to connect the appliance outlet to the TWPro, can also connect single wall connecting flue or vitreous enamel to TWPro. This has a flat design to give an instant transition from the appliance or connecting flue to TWPro in the shortest length.
- Add to basket
- Adaptors, Ø 150mm (6inch)
- £ 29,00
- Universal adaptor used as a increasing adaptor to connect the appliance outlet to the TWPro, can also connect single wall connecting flue or vitreous enamel to TWPro. This has a tapered design to allow a smooth transition from single wall to twin wall. Increases by a 25mm.
- Add to basket
- Adaptors, Ø 150mm (6inch)
- £ 29,00
- Universal adaptor to connect the appliance outlet to the TWPro, can also connect single wall connecting flue or vitreous enamel to TWPro. This has a tapered design to allow a smooth transition from single wall to twin wall.
- Add to basket
- Fire stops, Ø 150mm (6inch)
- £ 44,00
- The Firestop Cover Plate is used to cover an existing Firestop Plate. It gives the installation a pleasing finish, while still allowing enough air into the chamber without compromising the use of the Firestop Plate. It is attached to the underside of the Firestop Plate using magnets and spacers. It is important to use these spacers to allow the correct…
- Add to basket
- Fire stops, Ø 150mm (6inch)
- £ 145,00
- This kit comprises of 2 ventilated fire stops and a support clamp that can be used as a complete kit on a T600 all fuels firestop installation. Please note this installation allows 3 metres of vertical support.
- Add to basket
- Ø 150mm (6inch), Supports
- £ 34,00
- The Roof Support will rotate on 2 screws so that the flue can be installed vertically through the roof. The Roof Support is attached to the rafters in the roof space, allowing a fixed support before the Flue leaves the structure of the building. See loading data in guides.
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 33,00
- The Round Finishing Plate comes in two parts and is used to tidy the area around the flue as it passes through a non-combustible wall. This plate is attached to the wall where the flue is passing through at fixed 90°. Use silicone and screws to secure against the wall. 75mm wide
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 33,00
- The Round Finishing Plate comes in two parts and is used to tidy the area around the flue as it passes through a non-combustible wall. This plate is attached to the wall where the flue is passing through at fixed 45°. Use silicone and screws to secure against the wall. 75mm wide
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 33,00
- The Round Finishing Plate comes in one complete part and is used to tidy the area around the flue as it passes through a wall. This plate is attached to the wall where the flue is passing through at 45°. Use silicone and screws to secure against the wall.
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 33,00
- The Round Finishing Plate comes in one complete part and is used to tidy the area around the flue as it passes through a wall. This plate is attached to the wall where the flue is passing through at 45°. Use silicone and screws to secure against the wall.
- Add to basket
- Ø 150mm (6inch), Terminals
- £ 297,00
- Rotating cowls are one method of helping with the effects of down draft in the chimney system. The terminal has a rotating cover that will spin around in the wind equalizing the outlet velocity.
- Add to basket
- Ø 150mm (6inch), Terminals
- £ 31,00
- Used to cover the final section of TWpro to the elements when a third party terminal is being used. Please note we take no responsibility for the fixing of the third party terminal to the TWPro system Chimney.
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 222,00
- Fully lead free flashing with a Fast Flash adhesive base that is suitable for tiled or slate roofs. Fast Flash Flexible Roof Flashing is a polymer based flashing material with an aluminium mesh reinforcement. The lower surface, which has a butyl self-adhesive layer and is finished with a film to protect the flashing during storage and installation. Suitable for flues…
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 60,00
- Suitable for tiled roofs with external pipe diameters of 125mm to 225mm, the aluminium base size is 705mm x 501mm, the upstand is made from Grey SILICONE and is suitable for high temperatures.
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 205,00
- Fully lead free flashing with a Fast Flash adhesive base that is suitable for tiled or slate roofs. Fast Flash Flexible Roof Flashing is a polymer based flashing material with an aluminium mesh reinforcement. The lower surface, which has a butyl self-adhesive layer and is finished with a film to protect the flashing during storage and installation. Suitable for flues…
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 222,00
- Fully lead free flashing with a Fast Flash adhesive base that is suitable for tiled or slate roofs. Fast Flash Flexible Roof Flashing is a polymer based flashing material with an aluminium mesh reinforcement. The lower surface, which has a butyl self-adhesive layer and is finished with a film to protect the flashing during storage and installation. Suitable for flues…
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 205,00
- Fully lead free flashing with a Fast Flash adhesive base that is suitable for tiled or slate roofs. Fast Flash Flexible Roof Flashing is a polymer based flashing material with an aluminium mesh reinforcement. The lower surface, which has a butyl self-adhesive layer and is finished with a film to protect the flashing during storage and installation. Suitable for flues…
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 28,00
- Used to ensure water tightness in the passage through the roof. It also protects the flashing from extreme weather conditions. It should be installed about 25mm above the tallest part of the flashing. Once secure run a bead of silicone around the top edge and the flue to complete the water-tightness.
- Add to basket
- Ø 150mm (6inch), Supports
- £ 80,00
- A Roof Brace Kit can be used whenever there is a need to stabilise the chimney above the roof level. The roof brace kit must be used if the chimney extends 1.5 + metres above the roof. The arms can be adjusted from 1.5 metres to 2.3 metres in length.
- Add to basket
- Ø 150mm (6inch), Supports
- £ 98,00
- Wall support are to be used for lateral support only and should be use a minimum of every 3 metres. Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 80mm (minimum) and 420mm (maximum) adjustment from the wall surface allowing a 340mm adjustment. This…
- Add to basket
- Ø 150mm (6inch), Supports
- £ 81,00
- Wall support are to be used for lateral support only and should be use a minimum of every 3 metres. Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 130mm (minimum) and 210mm (maximum) adjustment from the wall surface allowing a 80mm adjustment. This…
- Add to basket
- Ø 150mm (6inch), Supports
- £ 77,00
- Wall support are to be used for lateral support only and should be use a minimum of every 3 metres. Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 80mm (minimum) and 130mm (maximum) adjustment from the wall surface allowing a 50mm adjustment.
- Add to basket
- Ø 150mm (6inch), Supports
- £ 31,00
- Wall support are to be used for lateral support only and should be use a minimum of every 3 metres. Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 50mm (minimum) and 80mm (maximum) adjustment from the wall surface allowing a 30mm adjustment.
- Add to basket
- Ø 150mm (6inch), Terminals
- £ 49,00
- Used to cap off the bottom or unused end of a 90/135 Tee, this is usually fitted to the bottom of a base support to allow easy removal for sweeping and access, this part includes a 10mm threaded drain to allow the connection of a drain pipe to carry away excess condense from the flue system.
- Add to basket