Skip to content- Ø 150mm (6inch), Supports
- £ 72,00
- The Retrofit base support is adjustable from 0mm to 120mm from the wall, it can be used in conjunction with 90° or 135° tees when fitted directly above. This item can also be used as a load bearing intermediate support on longer flue runs and can be retro fitted to make installation simpler. One support to be used on most…
- Add to basket
- Ø 150mm (6inch), Supports
- £ 203,00
- Adjustable Base Supports are used internally or externally to provide vertical support to the chimney. This support has a small levelling adjustment of 50mm to 80mm from the wall surface. Only recommended fixings should be used to fit this base support to the building surface.
- Add to basket
- Ø 150mm (6inch), Terminals
- £ 113,00
- Standard rain cap terminal with added 25mm square wire mesh to stop birds or vermin entering and blocking the flue way. Suitable for all fuel except gas.
- Add to basket
- Accessories, Ø 150mm (6inch)
- £ 44,00
- The Wall Sleeve is used to protect the chimney in the wall passage when the flue system passes to the outside wall. The gap between the flue and the Wall Sleeve can be filled with Rockwool. If going through the wall at 45 degrees, you will have to taper-cut the sleeve so that it fits flush in the wall. It…
- Add to basket
- Accessories, Ø 150mm (6inch)
- £ 185,00
- Mesh kit. For use when your flue passes through a loft space. The loft mesh kit is used to meet building regulations. Within the loft area the flue system must be boxed in or properly enclosed. This is in order to avoid combustible materials either being placed to close to or falling against the chimney. The system makes the installation…
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 41,00
- The Finishing Plate comes in two parts and is used to tidy the area around the flue as it passes through a non-combustible wall. This plate is attached to the wall where the flue is passing through between 90° and 60°. Use silicone and screws to secure against the wall.
- Add to basket
- Accessories, Ø 150mm (6inch)
- £ 44,00
- The Adjustable Wall Sleeve is used to protect the chimney in the wall passage when the flue system passes to the outside wall. The gap bewteen the flue and the Wall Sleeve can be filled with rockwool. This Wall Sleeve is precut at 45°, and is adjustable so it can be manually extended within wall.
- Add to basket
- Flashing, Ø 150mm (6inch)
- £ 41,00
- The Finishing Plate comes in two parts and is used to tidy the area around the flue as it passes through a non-combustible wall. This plate is attached to the wall where the flue is passing through between 45° and 60°. Use silicone and screws to secure against the wall.
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 40,00
- Our Base Cap with Drain is an essential component designed to cap off the bottom or unused end of a 90/135 Tee. It is typically fitted to the bottom of a base support to allow easy removal for sweeping and access, ensuring convenient maintenance of your flue system. This versatile part includes a 10mm threaded drain, which permits the connection…
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 341,00
- Our 90° Tee is a versatile component used when connecting the flue to the rear outlet of an appliance, especially when dealing with wood-burning stoves. This Tee features a 450mm branch, enabling direct installation onto the back of a wood-burning stove and passing through a standard brick wall. It is suitable for use with a wide range of solid fuel…
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 127,00
- Our 90° Tee is a vital component, typically used when connecting the flue to the rear outlet of an appliance. This Tee is specifically designed to facilitate this connection, ensuring optimal performance and safety for a variety of solid fuel and gas/oil appliances. It is suitable for use with woodstoves, gas coal effect fires, oil boilers, gas boilers, and various…
- Add to basket
- Elbows & Tees, Ø 150mm (6inch)
- £ 341,00
- Our Long 135° Tee is an essential component designed for providing convenient cleaning access at the base of your chimney. It serves as the first piece to be installed on the external wall and enables easy cleaning of the flue, ensuring your flue system remains efficient and well-maintained. This versatile Tee is suitable for use with a wide range of…
- Add to basket